DAWSON CZPT & MOULD Group
***EXTRUSION BLOW MOLDING Machine Specialist***
Our clients are all all around the entire world.
Vietnam, Australia, Indonesia, Malaysia, Thailand, Sri Lanka, Kazakhstan, Russia, UAE, Saudi Arabia, Malta, CZPTia, Italy, India, Syria, Ethiopia, Egypt, Sudan, Tunisia, Algeria, Kenya, Nigeria, South Africa, Zimbabwe, Mexico, Guatemala, Ecuador, Colombia, Venezuela, Peru….
Accumulation variety blow molding machine ABLD100
Suited for creating 100-250L HDPE Existence buoy, floater…
Equiped with MOOG parison controller
with SERVO Motor
Extrusion blow molding machine ABLD100
| extruder | |||
| 1 | CZPT diameter | 100mm | |
| 2 | L/D ratio | 24:one | |
| three | CZPT pace | 15~50r.p.m. | |
| four | CZPT motor | 45Kw | |
| five | Heating zone with cooling admirer | six zone | |
| six | Output/Capability | one hundred seventy Kg/hr(HDPE particle) | |
| 8 | Heating ability | 25.1 kw | |
| 9 | Vertical adjustment of head | 500mm | |
| ten | CZPT/Backward adjustment of head | 500mm | |
| eleven | Groove feed barrel cylinder | Have IKV | |
| 12 | Gear box | Challenging gear decelerator | |
| thirteen | Ladder and safety rails | Have | |
| Accumulator Head | |||
| 1 | Accumulator ability | 20L(15kgHDPE) | |
| two | Design | Very first in and initial out | |
| 3 | Heating zone | 6 zone | |
| four | Heating capacity | 25.1kw | |
| 5 | Max die&pin diameter | 450mm | |
| six | Die head axis with pre-blow | Ø120mm | |
| 7 | Accumulator thrust-out stroke measurement | Transducer Italy Gefran | |
| eight | Injection strain | twelve Mpa | |
| 9 | Extruder end | Have | |
| CLAMPING Device | |||
| 1 | Tie bar | Two tie bar | |
| 2 | Platen size | 900(W)X1400(H) | |
| three | Length of mold | 900-960mm | |
| four | Clamping drive | 780KN | |
| five | Close/Open stroke | 880-1700mm | |
| 6 | Mold fat | Max. 5000 kg | |
| seven | Clamping stroke measurement | Transducer Italy Gefran | |
| 8 | CZPT valve | ZheJiang Hitech | |
| 9 | Number of hydraulic cylinder | one | |
| ten | Large stress | fourteen Mpa | |
| 11 | Help areas for platen movement | Liner Xihu (West Lake) Dis. | |
| CZPT Program | |||
| 1 | Major motor/vice motor | AC15Kw/15Kw | |
| two | CZPT valve | ZheJiang Hitech | |
| 3 | CZPT pump | ZheJiang Hitech | |
| four | Oil tank ability | 850L | |
| 5 | Working force | 12 Mpa | |
| 6 | CZPT drinking water for oil | fixed | |
| seven | Control of oil degree | be observed dipstick | |
| CZPT Technique | |||
| one | Running strain | .8 Mpa | |
| 2 | Blow pressure | .eight Mpa | |
| 3 | Needle blow circuit | Higher & minimal stress | |
| four | Intermittent blow | Have | |
| five | Managed support air for parison | Have | |
| six | Air Valves | AIRTAC | |
| 7 | Quick exhaust for support air | Have | |
| PARISON Management | |||
| one | Programmer | JAPAN MOOG | |
| two | Servo valve | MOOG |
|
| 3 | Servo cylinder | Intergret of die head | |
| 4 | CZPT pack |
CZPT YOSHE Variable Displacement Piston Pumps |
|
| CZPTITY | |||
| one | Contactor |
Schneider |
|
| 2 | Total related load (approx.) |
114kw/h | |
| 3 | Average power usage (approx.) |
forty two kw/h | |
| H2o COOLING | |||
| 1 | CZPT drinking water use |
6000L/h | |
| 2 | Mold water usage |
6000L/h | |
| AIR Usage | |||
| one | Compressed air consumption | 1.two kgf/cm2, 3000 L/min | |
| OTHER Features | |||
| one | PLC control | MITSUBISHI | |
| 2 | Xihu (West Lake) Dis.n equipment interface | Hitech | |
| three | Recipe storage in challenging disk | Available | |
| HEATING Handle | |||
| 1 | Electricity source to heating component | Relay + Contactor | Japan Omron+Korea LG |
| 2 | Management | PLC controle | |
| three | Variety of therCZPTuple | K Variety | |
| four | Adjustable reduced and higher restrict alarm | Have | |
| five | Chilly begin prevention for screw | Have | |
| 6 | Alarm for therCZPTuple and heating aspect breakage | Have, heating element breakage by anperemeter | |
| 7 | Pre-heating operate | Have | |
| Die-ring AND Die-pin | |||
| 1 | a single sets of die & pin | 1 established according to buyer | |
| 2 | Check content | Purchaser provide 300kg content to seller for device screening | |
| Option | |||
| one | Base blow (hydraulic) and sealing device (pneumatic) | Double blow pin (such as broaden & up-down & parison seal) | |
| 2 | Robotic | Have | |
| three | CZPT Dimension | 6.8×3.3×5 | |
| four | Complete excess weight | 20 | |
